My first point of troubleshooting was to do a reset as directed in the manual. Reset the thermostat circuit breaker;
This system only has 2 zones.
How to reset dometic ccc2 thermostat. I connected both thermostats directly to the a/c unit with a separate telephone type cable and nothing. Release the mode and zone buttons. This will reset your thermostat and usually solves most issues.
Just took a couple times to relive the. To turn on the ccc 2 thermostat when the back light is off, first press any button to wake up the ccc 2 thermostat. To do a system reset:
Turn off the thermostat and press and hold the zone and mode buttons simultaneously. There is a 3a fuse on the control board of the rear a/c and it checks good (just realized there is probably one of these on the front unit too that has not been. To turn on the ccc 2 thermostat when the back light is off, first press any button to wake up the ccc 2 thermostat.
Wait a couple of minutes or up to 5 and then plug everything back in. Had to do the turn off sequence for 20 minutes more than once and also the thermostat reset about three times. Dometic ccc2 thermostat not working.
The led will display error. Keeping comfortable while traveling in your luxury sprinter van can often be a challenge due to rapidly changing temperatures during travel. Send a picture of your thermostat gone kaputs.
E1 is a comms issue, for me it was in the winter last time this year, my gut was it was a static electricity issue only. If the thermostat comes on but does not provide temperature control, switch it to a lower temperature than its operating tempera Ensure the main power is switched on;
However, after doing a factory reset, zone 1. The screen shows nothing (blank). However, even after resetting the thermostat multiple times to read the dip switches, heat pump (hp) mode does not show up on the thermostat.
When i power on my dometic ccc2 thermostat & press 'zone/mode. Dometic ccc2 thermostat frozen in place. I do have a spare thermostat so i swapped them and still nothing.
Before you check your manual, one simple way to do this is to simply unplug from all power supplies and battery disconnect. Videos you watch may be added to the tv's watch history and influence tv recommendations. Turn the thermostat off, and turn power to the ac units off and on.
Try a factory reset simultaneously press and hold zone and mode button sent from my moto z3 using tapatalk I have a 2014 cedar creek fifth wheel with the dometic ccc2 system. My thermostat has just frozen in place, zone 1;
Dometic thermostat missing zone 2. Vocational, technical or trade scho. Press the mode button to cycle through the mode options.
Then press and release the on/off button. Are changed, a system reset will need to be done before the ccc 2 thermostat will recognize the updated selection. My digital thermostat has a blinking zone one.
My converted unit works correctly in cool mode. The lcd will display the last programmed settings. Dometic thermostat won’t turn on.
Then turn the thermostat on and see if it. I made sure the mode was in the off position and powered down the thermostat. I can't reset it, i can't turn it off, i can't use the other buttons to change anything.
Only the time of day will display when the How do i reset my dometic thermostat? I'm supposed to have 4 programmable zones, however, i rec'd a e1 error message and performed a system reset to restore factory settings.
Hi, zone 2 on my thermostat would not work. At this point, i have a brand new unmodified heat pump that works as expected with the new ccc2 thermostat. Loss of communication between the ccc 2 thermostat and all system power module boards.
The reset system won’t work if you have a blown fuse, burned wiring, loose wiring, and other mechanical failures that impede the thermostat’s operation. In case your thermostat won’t turn on here is how to solve the problem. The lcd will display “init” and all available zones.
Make sure the ccc 2 thermostat is in the off mode. Loss of communication between the ccc 2 thermostat and an individual system power module board. I tried to unplug it.
Simultaneously press the mode and zone buttons. Your unit can get into a situation where the thermostat is not communicating with one or both upper boards. Then press and release the on/off button.
To turn off the ccc 2 thermostat press the on/off button and release. I have a 2013 heartland landmark key largo w/two dometic cc2 thermostats. If playback doesn't begin shortly, try restarting your device.